Informative Guide to Resolve Netgear Router Red Light Issue

Whenever you see a red light, what is the first thing that comes to your mind? Danger, isn’t it? Taking this into consideration, if the LED on your Netgear router is flashing red, then it is a sign of danger too. It means that literally, anything can be wrong with your device even if you have successfully performed setup.

But, why fear when we are here? In this post, you will get familiar with various ways through which troubleshooting the issue at hand will become a piece of cake for you.

[Resolved] Netgear Router Red Light Issue

Before you make your way to the troubleshooting hacks mentioned below, restart your Netgear router. We are suggesting you this because this hack has helped many users. And there are high chances that it might help you out too. On the off chance, this thing does not work for you; following the troubleshooting hacks mentioned below is your only choice.

  1. Check the Power Supply

If your Netgear router is getting an inadequate power supply, it is the number one reason why you are facing the red light issue. Therefore, check the wall socket through which your device is getting electricity. Is it damaged? Even by one percent, if it is, then plugging your Netgear router into a different wall socket is recommended.

Are you done following this hack? Well then, try to access the page. Are you able to? Well then, it is clear that you are still stuck with the red light issue. But, anyway, you can follow the hack mentioned next.

  1. Switch the Connection Source

A wireless connection might seem like a modern way of connecting devices, however, it isn’t reliable. Therefore, if you have connected your devices wirelessly, then it is advised that you change that without giving it a second thought.

Instead of a wireless connection, use a wired connection source to connect the networking devices. Just make sure that the connection is finger-tight at all costs. Apart from that, the Ethernet cable should be properly plugged into the ports of your devices.

  1. Pull the WiFi Devices Closer

While setting up your Netgear router, did not check where you are placing it? Obviously not, otherwise, you would not be in this mess. Too much distance between your devices can create a communication gap between them. In technical terms, your devices will not be able to transmit signals properly.

Thus, you should reduce the distance between them. However, ensure that your devices are not clinging to each other. This can cause their wireless signals to clash. You can forget about ever troubleshooting the Netgear router red light issue then.

  1. Perform Netgear Firmware Update

Updating the firmware of your Netgear router can also be of aid considering you are troubled because of the red light issue. If you are one of those users who are worried about how will you go about the Netgear router firmware update process, stop stressing.

Following the steps given here will help you to update your router with ease:

  • Open an internet browser on your system.
  • Access the address bar and type
  • Hit Enter.
  • On the Netgear router login page, enter the login credentials.
  • Hit Log In.
  • Click the Firmware Update button under Settings.

Once you have clicked on the Netgear firmware update button, give your router some time to get updated. Do not interrupt the process. Otherwise, you will end up facing another issue called Netgear router firmware update failure.

  1. Reset the Netgear Router

Although these hacks will be able to help you to troubleshoot the Netgear router red light, in case, you are still going nuts because of the same, restore your device to its default factory mode.

The following section will help you to restore your device to its default mode:

  • Look at the right and left sides of your router.
  • Locate the Reset button.
  • Press it.
  • Hold on for some time.

Before you can even bat an eye, you will be able to restore your router to its default factory mode. If you want, you can also reset your device by accessing the web user interface of your device. Then, set up your device using the admin details.

Bonus Tip

Many users have been encountering issues related to the Netgear routers. In order to avoid ninety of them in the future, consider getting rid of WiFi interference. You can do so by keeping cordless phones, baby monitors, refrigerators, microwave ovens, mirrors, fish tanks, washing machines, treadmills, televisions, and Bluetooth speakers.

The Bottom Line

You will definitely be able to troubleshoot the Netgear router red light issue after going through the hacks mentioned above. Would you like to share with us which was the hack that helped you out the most in fixing the red light issue?

Whether the answer is a yes or no, we would like it if you will leave your feedback via the comment section. Surely your feedback will matter to your fellow readers as well.

Leave a Reply

Your email address will not be published. Required fields are marked *